BMW X5 Owners & Service Manuals

BMW X5: Checking Camshaft Timing On Left Side (N62/N62TU)

BMW X5 (G05) 2019-2024 Service & Repair Manual / Engine / Engine (N62TU V8) / Camshaft / Checking Camshaft Timing On Left Side (N62/N62TU)

Special tools required:

(cylinder bank 5 to 8)

Necessary preliminary tasks:

Remove all spark plugs on cylinder bank 5 to 8.

If necessary, remove fan cowl.

IMPORTANT: Screw (1) is a special screw and must not be replaced with a normal M8 screw.

Release screw (1).

Unclip oil line (3) from retainers (2) and remove.

Camshaft
Fig. 329: Identifying Retainer And Screw

Crank engine at central bolt in direction of rotation to firing TDC position of 1st cylinder.

NOTE: With 1st cylinder in firing TDC position, cams of inlet and exhaust camshafts at 5th cylinder point upwards at an angle as shown in illustration.

Camshaft
Fig. 330: Locating Cam Lobe Position

NOTE: Alignment hole for TDC position is at front on timing case cover.

Crank engine at central bolt and secure vibration damper with special tool 11 9 190 in firing TDC position of 1st cylinder.

Camshaft
Fig. 331: Identifying Special Tool (11 9 190)

IMPORTANT: When the engine is shut down, the inlet and exhaust adjustment unit is normally locked in its initial position.

The situation may arise in some individual cases where this initial position is not reached and the camshaft can continue to be rotated in the adjustment range of the adjustment unit.

In order to avoid incorrect timing adjustment, it is essential to check the locking of the adjustment unit and if necessary perform locking by rotating the camshafts.

Checking locking of inlet adjustment unit in initial position:

Engage hexagon head of inlet camshaft and attempt to rotate inlet camshaft carefully against direction of rotation.

If there is no fixed connection between inlet camshaft and inlet adjustment unit, rotate inlet camshaft against direction of rotation as far as it will go.

The inlet adjustment unit is locked in the initial position when the inlet camshaft is non-positively connected to the inlet adjustment unit.

Camshaft
Fig. 332: Rotating Inlet Camshaft

Checking locking of exhaust adjustment unit in initial position:

Engage hexagon head of exhaust camshaft and attempt to rotate exhaust camshaft carefully in direction of rotation.

If there is no fixed connection between exhaust camshaft and exhaust adjustment unit, rotate exhaust camshaft in direction of rotation as far as it will go.

The exhaust adjustment unit is locked in the initial position when the exhaust camshaft is non-positively connected to the exhaust adjustment unit.

Camshaft
Fig. 333: Rotating Exhaust Camshaft

IMPORTANT: If the inlet or exhaust adjustment unit of the camshafts "cannot" be locked as described, the adjustment unit is faulty and must be replaced.

Place special tool 11 9 461 on inlet camshaft and check timing.

NOTE: The timing is correctly adjusted when special tool 11 9 461 rests flat on the cylinder head or protrudes by up to 0.5 mm to the exhaust side.

Remove special tool 11 9 461 from inlet camshaft.

Camshaft
Fig. 334: Identifying Special Tool (11 9 461)

Place special tool 11 9 462 on exhaust camshaft and check timing.

NOTE: The timing is correctly adjusted when special tool 11 9 462 rests flat on the cylinder head or protrudes by up to 0.5 mm to the exhaust side.

If necessary, adjust camshaft timing on left side.

Camshaft
Fig. 335: Identifying Special Tool (11 9 462)

Remove all special tools.

IMPORTANT: Screw (1) is a special screw and must not be replaced with a normal M8 screw.

Clip oil line (3) into retainers (2).

Insert screw (1) and tighten down.

Assemble engine.

Camshaft
Fig. 336: Identifying Retainer And Screw

READ NEXT:

 Checking Camshaft Timing On Right Side (N62/N62TU)

Special tools required: 11 9 190 11 9 461 11 9 462 (cylinder bank 1 to 4) Necessary preliminary tasks: Remove servomotor from right eccentric shaft. Remove right cylinder head cover. Remove

 Adjusting Camshaft Timing On Left Side (N62/N62TU)

Special tools required: 11 9 190 11 9 460 11 9 461 11 9 462 11 9 463 (cylinder bank 5 to 8) Necessary preliminary tasks: Check camshaft timing on left side. Remove left timing case cover.

 Removing And Installing/Replacing Rocker Arms On Left Inlet Side (N62 From 9/03 And N62TU)

Special tools required: 11 9 470 11 9 473 (cylinder bank 5 to 8) Removal of rocker arms is described separately from installation. Necessary preliminary tasks: Remove servomotor for left eccentr

SEE MORE:

 BMW Drive Recorder

Principle The BMW Drive Recorder stores brief video recordings of the vehicle surroundings, e.g., to document surrounding traffic. General information There are various ways for storing video recordings: Automatic storage of the recording. The function allows the documentation of the event of an

 Renaming a driver profile - Driver profiles

Renaming a driver profile Non-ConnectedDrive countries: 1. "CAR". 2. "Driver profiles". As an alternative for Steps 1 and 2, the profile image can be tapped in the top status bar. 3. Select driver profile. 4. "Settings". 5. Enter a profile name. 6. Select the icon. ConnectedDrive countries: T

© 2019-2024 Copyright www.bmwx5info.com