BMW X5 Owners & Service Manuals

BMW X5: Pre-conditioning through Remote Engine Start

BMW X5 (G05) 2019-2025 Owners Manual / Controls / Climate control / Pre-conditioning through Remote Engine Start

Principle

Pre-conditioning cools or heats the car's interior prior to departure to a comfortable temperature.

The system automatically cools, vents, and heats depending on the interior, external, and set temperature.

Snow and ice may be removed more easily.

The system starts the engine automatically and allows it to run for a limited period of time.

Safety information

DANGER

If the exhaust pipe is blocked or ventilation is insufficient, harmful exhaust gases can pollute the area in and around the vehicle or enter into the vehicle. The exhaust gases contain pollutants which are colorless and odorless. In enclosed areas or areas with insufficient ventilation, exhaust gases can also accumulate outside of the vehicle. There is danger to life.

Keep the exhaust pipe free and ensure sufficient ventilation. Do not switch on stationary climate control in enclosed areas or areas with insufficient ventilation, e.g. in enclosed garages.

Warning

When stationary climate control is in operation, high temperatures can occur underneath the body, for instance caused by the exhaust gas system. If combustible materials, such as leaves or grass, come in contact with hot parts of the exhaust gas system, these materials can ignite. There is a risk of fire. Make sure that no combustible materials can come in contact with hot vehicle parts during stationary climate control operation, e.g. leaves, grass, gas, gasoline, oil or other combustible objects.

Functional requirements

Enabling the automatic engine start function

The automatic engine start must be enabled before using the system. Otherwise, the engine cannot switch on automatically to climatize the car's interior.

Via iDrive:

1. "CAR".

2. "Settings".

3. "Climate control".

4. "Preconditioning/ventilation".

5. "Remote Engine Start".

6. "Starting engine for clim. control".

7. Confirm the disclaimer.

Switching on/off directly

General information

The system switches off automatically after approx. 15 minutes.

For reasons of safety, the system can only be switched on twice consecutively. The system will be available again as soon as the drive-ready state is activated and deactivated again.

Switching on via iDrive

1. "CAR".

2. "Settings".

3. "Climate control".

4. "Preconditioning/ventilation".

5. "Start now".

Switching on/off via vehicle key

The system can be switched on and off using the vehicle key.

Press the button on the vehicle key three times within 1 second.

After operating the vehicle key, it will take approximately 3 seconds until the engine is switched on.

To switch off the system, press the button again three times.

Switching on via BMW display key

1. Switch on the display of the BMW display key.

2. "Preconditioning setting".

3. Tap on the icon.

4. "Activate now".

5. "Start".

Switching off via BMW display key

1. Switch on the display of the BMW display key.

2. "Preconditioning setting".

3. Tap on the icon.

4. "Stop".

Switching off with the Start/Stop button

The system can be switched off directly as follows: pressing the Start/Stop button, without operating the brake pedal.

Switching on via departure time

General information

Scheduled departure times can be set up in the system to ensure a comfortable interior temperature in the vehicle at the time of departure.

The departure time is preselected in two steps:

The climate control function will start approximately 10 minutes before the set departure time and continue for approximately 5 more minutes after the departure time.

A minimum of 10 minutes should pass between setting/activating the departure time and the planned departure time to allow a sufficient period of time for the climate control.

For reasons of safety, the system can only be switched on once. The system will be available again as soon as the drive-ready state is activated and deactivated again.

Observe the information about the intended use of the vehicle.

Additional information: For Your Own Safety.

Adjusting the departure time via iDrive

1. "CAR".

2. "Settings".

3. "Climate control".

4. "Preconditioning/ventilation".

5. "Departure plan".

6. Select the desired departure time.

7. Set the departure time.

8. Select day of the week, if needed.

Adjusting the departure time via BMW display key

1. Switch on the display of the BMW display key.

2. "Preconditioning setting".

3. Tap on the icon.

4. Select the desired departure time.

5. Set the departure time.

6. Select day of the week, if needed.

7. "OK".

Activating the departure time via iDrive

1. "CAR".

2. "Settings".

3. "Climate control".

4. "Preconditioning/ventilation".

5. "Departure plan".

6. Activate the desired departure time.

Activating the departure time via BMW display key

1. Switch on the display of the BMW display key.

2. "Preconditioning setting".

3. Tap on the icon.

4. Activating the desired departure time:

Tap on the icon.

Display

In the instrument cluster: The engine runs for the purpose of operating the pre-conditioning.

The vehicle is not ready to drive.

The icon on the automatic climate control signals an activated departure time.

The icon flashes while Remote Engine Start is running.

Confirmation signals from the vehicle

The activation of the system is confirmed by flashing twice.

The parking lights are switched on as long as the system is switched on.

READ NEXT:

 Ambient air package

Principle The Ambient Air Package can be used to clean and scent the interior air with high-quality fragrances. General information Two different fragrances can be selected in the vehicle. A variety o

 Interior equipment

 Integrated Universal Remote Control

Principle The integrated Universal Remote Control in the interior mirror can operate up to 3 functions of remote-controlled systems such as garage door drives, barriers, or lighting systems. General i

SEE MORE:

 Regulator

REPLACING VOLTAGE REGULATOR Necessary preliminary tasks: Switch off ignition. Disconnect battery negative lead. Notes on removing and installing electronic control units. Remove alternator. Bosch: Release protective caps (1). Fig. 40: Inserting Screwdriver Between Cover And Threaded Pin Bos

 Operating via the Controller

Opening the main menu Press the button. The main menu is displayed. Selecting a menu Selecting menu items 1. Turn the Controller until the desired menu item is highlighted. 2. Press the Controller. Select a widget 1. Move the Controller in the main menu to the right. 2. Turn the Controller until

© 2019-2025 Copyright www.bmwx5info.com